PVC ceiling is based on pvc plastic buckle board as a raw material for ceiling decoration, such a ceiling waterproof, scrub resistance, compared to aluminum ceiling, texture and decorative sense better, and lower cost. PVC ceiling also has good thermal insulation properties. The following Xiao Bian introduces the characteristics of PVC ceilings and pvc ceilings.
PVC buckle plate ceiling characteristics
1, light waterproof and acid and alkali
The PVC buckle board ceiling is not only light weight, waterproof and moistureproof, but also has the characteristics of strong resistance to acid and alkali. It is an ideal material for ceiling installation in kitchens and bathrooms. General PVC buckle plate ceiling is also the main selection of kitchen and toilet ceiling.
2, affordable
PVC ceiling ceiling material is more common, and its price is much lower than other ceilings such as plasterboard ceilings and mineral wool ceilings. It is a relatively popular decoration material.
3, non-toxic and environmentally friendly
Many people are concerned that PVC materials are odorous and toxic. In fact, the PVC ceilings of large brands are completely non-toxic and odorless. They have no stimulative effect on human skin or respiratory system. For those who are allergic to wood and paint, PVC ceiling is very suitable for use in the kitchen or bedroom.
4, easy to install and remove
The PVC ceiling board ceiling profile is easy to install and it is very convenient if damage occurs. As long as one end of the bead is removed, the board is pulled out from the bead piece by piece, the damaged board is replaced with a new board, and then the pressure plate is reinstalled. However, during the replacement, the color difference of the PVC ceiling material should be minimized.
PVC ceiling plate installation steps
1, according to the design elevation on the wall around the bullet, the bullet line should be clear, accurate position, the level of allowable deviation ± 5mm.
2. Fix the keel along the elevation line. The function of the side keel is the sealing of the edge of the ceiling. The common specification of the side keel is 25*25mm. Its color should be the same as that of the PVC buckle plate. The side keel is fixed on the wall column with cement nails.
3, to determine the keel position line, because each piece of PVC gussets are formed veneer, generally can not be cut into pieces, in order to ensure the integrity of the ceiling finish and installation reliability, according to the size of the aluminum gusset plate, and The size of the suspended ceiling is used to arrange the structural dimensions of the ceiling frame. The basic layout of PVC gussets is: When the plate combination is complete, when the edges are surrounded, the edges of the rims must be symmetrical and uniform, and the arrangement of the arranged positions of the dragon skeletons should be arranged on the upper side of the elevation line.
4, the main keel lifting point spacing, according to the design recommended series selection, the middle part should be arched, keel arching height is not less than 1/200 of the room surface span. Correct the position and height of the main keel after installation. To control the smoothness of the skeleton of the dragon, firstly pull out the vertical and horizontal control lines, and from one end, adjust the suspending height of the boom while installing it. After the large surface is flattened, some single keels with curved edges and edges are adjusted until they meet the requirements.
5. The boom should be straight and have sufficient bearing capacity. When the boom needs to be long, it must be welded firmly and the weld is even and full. For anti-rust treatment, the boom should not exceed 300mm from the end of the main keel. Otherwise, a boom should be added to prevent the main keel from falling. The secondary keel (below the middle keel or small keel) should be installed close to the main keel.
6, a comprehensive correction of the main and sub-keel position and level. The connectors shall be installed in a wrong position. Check the installed ceiling frame. It shall be firm and reliable. Only after complying with relevant regulations can the next construction be carried out.
7. When installing the PVC pinch plate, the secondary bone should be straightened. The buckle plate shall be flat and shall not warp. The error of the flatness of the ceiling shall not exceed 5mm.
Pvc buckle buy
1. The cross section of pvc plastic buckle plate is honeycomb shape, which is also the most direct way to distinguish between pvc plastic buckle plate and aluminum buckle plate. When picking, you should pay attention to whether the two sides of the pvc plastic gusset are smooth, and there are no undulations or height differences.
2, the hand bending is not deformed, full of elasticity; the sound of the surface striking by hand is crisp, indicating that the material has strong toughness. Poor plastic pvc plastic gussets are very brittle and even cracked;
3, smell pvc plastic buckle plate has a taste, if there is a clear odor, then it shows its poor environmental performance; can require the production or distribution unit to produce its inspection report, but also should pay special attention to whether the oxygen index is qualified, it must be greater than 30 Only in favor of fire prevention.
4, pvc plastic buckle surface should be flat, color patterns should be clear.
Editor's summary: About the characteristics of the PVC buckle ceiling and pvc buckle ceiling installation steps are introduced here, and hope to be helpful to everyone. If you want to know more about yourself, you can follow the information on this site.
Ceiling step pvc ceiling price living room ceiling decoration renderings Mediterranean indoor ceiling Chinese corridor ceiling
Iron 3 Oxide,Iron Lll Oxide,Ferric Oxide Red,Transparent Iron Oxide
TINOX CHEMIE GMBH , https://www.tinoxglobal.com