Home>Bearing knowledge>SKF imported bearing burnout inspection analysis and avoidance methods

/*728*90 created on 2018/5/16*/ var cpro_id = "u3440131";

SKF imported bearing burnout inspection analysis and avoidance methods

---

/*250*250 was created on 2017/12/25*/ var cpro_id = 'u3171089';

SKF imported bearings of automobile rear axles are important parts for driving wheel movement. SKF imported bearings mainly accept bending and torsion composite moments; they can accept certain impact loads together. Semi-axes are generally selected from medium carbon alloy steel after induction and quenching. Hardening; hardened layer depth 4 6mm; hardness is 50 ~ 55HRC. Found in SKF imported bearings; often exhibits the appearance of SKF imported bearings burnt; seriously affects SKF imported bearing product production and workpiece induction quenching quality. Inspection found; SKF imported bearings burned The bad areas are located in the induction circle 225. The left and right parts; the expansion to the two sides is a regular failure feature.
The professor pointed out that when the half shaft is heated in the inductor; the heat generated by the inductor is not only heating the workpiece; there are three methods of heat loss.
(1) Radiating heat to the surrounding area. There are magnetizing magnets, insulating varnish and glass cloth cloth on the induction coil. This way, the heat loss is small; and the heat dissipation is uniform; the effect on the sensor burnout is small.
(2) The cooling water takes away the heat. This heat reduces the temperature of the sensor; makes the induction heating work safely. The experiment finds that the water inlet is between 0-180 degrees; the water temperature is low; the cooling water heat exchange is outstanding; the water flow is smooth; The water temperature rises little, beyond 180. In the future; because the water flow path is long; the water temperature is increased; the water temperature rises to make the heat exchange worse; the temperature is likely to form a part of the sensor (such as the 225. The primary cause of the induction coil burnout.
(3) The heat of the induction coil is transmitted to the connecting plate; the current density of the connecting plate part. ㄋ孛婊螅 垢 垢 蛩 停 停 停 停 θ θ θ θ θ θ θ 在 在 在 在 在 在 在 在 在 在 在 在 在 在 在 在 在 在 在 在 在The temperature sensing ring is close to the connecting plate; the heat conduction is good, and the 90-270 degree sensing ring is far away from the connecting plate; the heat conduction is poor; the temperature of the induction coil in this area is increased; it is easy to exhibit in this section. The ring burned out. The difference in the heat of the induction coil is different. The induction coil is close to the heat storage in the 225-degree area and has poor conduction; therefore, the part is easy to show the appearance of the induction coil.

---

Recommend to friends comments close window

Bearing related knowledge

Misunderstandings about the inspection and inspection and quality of KOYO bearings SKF bearing extra life and additional dynamic load bearing support selection to consider the problem of bearing steel casting diesel engine bearing burning precautions (2)

This article links to http://
Please indicate China Bearing Network http://

Previous:The layout of the shaft is composed of the following: The front and rear code of the German FAG bearing (1)

The Wire Thread Insert is a kind of threaded fastener,and the colored wire Thread Insert is a kind of coating product which is used under special requirement or link, and the color is mainly used to distinguish the specifications and uses.

Characteristics of colored wire thread insert:

1. It can clearly distinguish different specifications and different use products, and facilitate the batch management of storage.

2. With different colors, the colored wire thread insert is able to make a sharp contrast with the pressed parts to facilitate the maintenance of the work.

Coated Thread Insert

Wire Insert,Unf Coated Thread Insert,Wire Thread Insert For Aluminium,Coated Thread Insert

Xinxiang Donghai Industry Co., Ltd. , https://www.thaicoil.com