[Suzhou Home Network] Today, Xiaobian collected the most valuable decoration experience of the home improvement "predecessors", using the "unprofessional" language, so that everyone can easily grasp the problems that home decoration needs to pay attention to.
About hydropower
1. Waterproof construction should be waterproof with coating film.
2. The waterproof project should be carried out after the concealed construction is completed and accepted.
3. After the waterproof construction is completed, do 2 water storage tests.
4. The waterproof layer of the bathroom should be no less than 1.8cm.
5. Floor drain, Guardian angle, pipeline and other places should do more than one waterproof project.
6. Floor drain should use deodorant type.
7. The hot and cold water pipes should be left hot and right cold.
8. Try not to go from the ground.
9. The cold water pipe should have a protective layer of 1cm on the wall surface. The hot water pipe should have a protective layer of 1.5cm on the wall surface, so the groove should be opened deep.
10. Install the PPR tube to consider the thickness of the tile so that the tube will not be exposed.
11. People who cook regularly know that cooking usually takes only a few minutes, but washing vegetables takes a long time, so the water gate must buy big.
12. The faucet and the basin should be matched, otherwise it may not be installed.
13. Do not use cement when installing the toilet. Use silica gel.
14. Be sure to pay attention to the protection after the toilet and faucet are installed.
15. Consider the pit pitch of the toilet when purchasing the toilet.
16. Before installing the washing machine, consider whether to use the upper drain or the lower drain.
17. It is best not to install a telephone in the bathroom, it is easy to get wet.
18. Consider the dimensions before installing the mirror in the bathroom, otherwise the mirror headlights are easy to install too high.
19. It is best to leave the inspection holes in the bathroom.
20. Strong electricity and weak electricity cannot be worn in the same pipe.
21. The wiring principle of the socket is left zero, right phase, and grounded.
22. The power socket is 30cm away from the ground and the switch is 140cm away from the ground.
23. Do not install the switch behind the door.
24. The indoor outlets are more and more good.
25. High-power appliances should use 16A sockets, such as air conditioners.
26. The cassette must be of high quality.
27. The cassette should be matched with the panel, otherwise it may not be installed.
28. Within the PVC wire tube, the cross-sectional area of ​​the wire shall not exceed 40% of the cross-sectional area of ​​the wire tube.
29. If you install air conditioner in your bedroom, you can't put it on the bed.
30. The air-conditioning opening should be inclined outwards, otherwise the rain will come in when it rains.
31. The luminaire should consider double control as much as possible.
32. It is best to install a splash-proof socket in the bathroom.
33. Try to install sockets on the balcony as much as possible.
34. The wire trough should be horizontally and vertically arranged for future use.
35. The public flue should be fitted with a check valve.
About Mason
1. Cement cannot be used beyond the date of manufacture by 3 months.
2. Different varieties and labels of cement can not be mixed.
3. Yellow sand must use river sand, taste can be judged with the mouth, because the river sand does not contain salt, it should not be salty.
4. Walls and floor tiles should be immersed in water for more than 2 hours.
5. Walls and floor tiles would rather buy more pieces, don't buy less, otherwise it is prone to color difference.
6. There can be no two rows of non-complete bricks on one wall.
7. Clean the tiles immediately after the seam is completed.
8. The floor is covered with light-colored marble bricks, and the back of the stone should be waterproof.
9. The angle of the corner should be cut at a 45-degree angle.
10. The floor tiles should be inclined to the floor drain, otherwise it will accumulate water.
11. Wall tiles hit the pipe mouth to take the form of cutting, so it looks like a whole piece of brick.
12. The ground marble should be dry.
13. Floor tiles must be stain-resistant and non-slip. Don't just look good.
14. Matte tiles are difficult to clean and are not recommended.
15. Pay attention to the drainage direction when laying the floor tiles on the balcony.
About woodworking
1. The ground keel is best used to dry larch.
2. Large pieces of wood should be sawed and air dried after purchase.
3. Woodworking must first play the horizontal line of the house.
4. When the color panel enters the field, use the paint brush once and prevent it from getting dirty.
5. The ceiling fan cannot be mounted on the ceiling keel.
6. Pre-color picking when constructing the color panel.
7. The hanging rib of the ceiling shall not be more than 300mm away from the wall.
8. The plasterboard should be fixed with a countersunk head tapping screw, and it should enter the board surface 1-2mm, and do anti-rust treatment, can not use gun nails.
9. The distance between the plasterboard and the nail must not exceed 200mm.
10. The plasterboard should be kept at a gap of 3 mm with the wall for crack protection.
11. It is best to do a positive angle strip for protection at the corner of the plasterboard.
12. The top and bottom of the wooden door should be painted.
13. The bottom of the bathroom door cover should be waterproof.
14. The size of the doors in each room should be the same.
15. Furniture should try to buy finished products, do not let woodwork do, otherwise it is easy to have a variety of problems.
16. It is best to buy the whole cabinet, just like the furniture, don't let the woodwork do it, otherwise the quality is not likely to be good, and the design is not good enough.
17. Do not use dark track for the sliding door made by woodwork, otherwise it will not be repaired later.
18. The bathroom with a small area should be moved as much as possible because the sliding door saves space compared to opening the door.
19. The error of the flatness of the floor wood keel should not exceed 5mm.
20. The floor should be laid at 30 degrees or 45 degrees, leaving a gap of 2-3 mm between the board and the board, and the seams should be staggered.
21. Leave a gap of 8-10mm between the floor and the wall.
22. When the length of the composite floor exceeds 8m, consider the expansion joint.
23. Minimize the use of MDF as a door cover.
24. Hinge and hardware must use high quality products.
25. Yuba should be mounted on the wooden keel and cannot be mounted directly on the ceiling.
About paint
1. Do not mix water in the construction of medium and dark latex paints, otherwise color difference will occur.
2. Gypsum board joints should be bandaged, otherwise it will be easy to crack after a few months.
3. Where there are gaps in the wall, polyester cloth should be placed.
4. The original putty on the wall is best removed, or brushed once to seal the glue.
5. Try to buy paints of famous brands. No matter how the decoration company or foreman recommends it, try not to use it.
6. Do not paint when the weather is too humid.
7. The construction of the next paint must be carried out after the previous paint has dried out. Similarly, the polishing of the paint and paint should be carried out after it has completely dried out.
8. Metallic paint should be rustproofed.
9. If the temperature is too low, it will cause wrinkles and orange peel on the paint surface, which will seriously affect the construction quality. Therefore, when the temperature is lower than 5 degrees, it is not suitable for paint construction.
10. When painting the door, use a textured paper to hold the hinge and the door lock.
11. When the weather is too hot, pay attention to ventilation after painting.
12. When painting wallpaper, brush the oil on the wall.
13. When affixing wallpaper, remove the panel of the switch and socket beforehand.
14. Bright, mercerized latex paint should be completed at one time, otherwise it will easily appear chromatic aberration.
15. After the baseboard is installed, use putty and latex paint to make up the seam.
As the different workpiece machined and working condition, we can offer and design the best router bit for your
situation. With their unique properties, our OPT woodworking cutters ensure max. machining productivity, and can be re-sharpened many times without affecting the original profile.
We have a world-class technical team, and can design cutting tools as individual situation.You can send us tool samples for checking, or wood samples for designing the right tools.
Flexible in order quantity:
Samples can be provided before mass production, and MOQ can be discussed accordingly.
PRODUCT DETAIL:
PRODUCTING PROGRESS:
PAYMENT AND DELIVERY:
PRODUCT EQUIPMENT :
ABOUT US :
We are specialize in manufacturing PCD diamond tools and Carbide tools. Our major product inclulde PCD Inserts , PCD Reamers , PCD End Mills , PCD Taps, Cabide Inserts,Carbide Drills, Carbide Reams, Taps etc.,
We also offered customized cutting tools per drawings, and provide package according to customer requirements. We manufacture a series range of cutting tools for machining of Cast iron, Aluminium alloy and Non-Ferros metal, it is widely used in all major sectors like Automobiles, Engineering, Aerospace, Aviation and 3C industry. Premium quality of raw material is used in the production and strict examination during processing with advanced equipment, so our client are satisfied with our reliable quality and on-time delivery.
Our best selling of cutting tools include PCD Inserts, PCD End Mill , PCD Ball Nose Mill, PCD Reamer , Carbide Taps , Carbide End Mill , Special Form Cutter and many more. For these years we have been made a large forward in the technologies of manufacturing cutting tools. With high quality on performance and price, our product sells well both on domestic and overseas market. And we will always focus on the quality and best service, to make long business relationship.
quanlity control:
We have dedicated team of quality control and precise equipment to keep good and stable performance for our products and processing services.
PCD Wood Router Bit
PCD Router Bits,Diamond Drill Bit,Diamond Router Bits,PCD Wood Router Bit
OPT Cutting Tools Co., Ltd. , https://www.optdiamondtools.com