The hinge is one of the necessary hardware for the cabinet cabinet to engage with the door panel and to repeatedly open and close. Since the opening frequency of the door panel is the highest in use. Therefore, the quality of the hinge is particularly important. Opening and closing effects and durability, natural, smooth, and silent are basic requirements. Secondly, the adjustability: up and down, left and right, front and rear adjustable range is 2mm; opening angle should be minimum of 95 and certain corrosion resistance and safety. The good hinge is very hard by hand, the reed is solid, the mechanical folding is not shaking, it will rebound automatically when it is closed to 15 degrees, and the resilience is very uniform.
The hinges are divided into ordinary and fast loading. The block hinges can quickly realize the separation and combination of the door panel and the cabinet. The price of the two will be 3 or 4 times worse. The domestic hinges can be used. The foreign cabinets use the quick hinges because of foreign The labor cost of the installation workers is very high. In contrast, the use of quick-fit hinges saves labor, and the overall cost is cheaper. The difference in national conditions has caused differences in material use.
Good quality hinges can be switched tens of thousands of times and are easily flexible. Two interlocking hinges were installed at the corner of the cabinet door, and the space was well utilized.
The technical function and quality of the slide rail should be second only to the hinge. The better sliding function should be the natural combination of the smoothness and the load-bearing effect. Under the rated load-bearing conditions, there is no obvious friction and jamming phenomenon, and the sliding is smooth. It plays an important role in the use and life of the drawer.
Hand in hand should be beautiful in appearance and fine in workmanship. The metal surface is free of rust, the coating is flawless, and there is no burr sharp edge. Generally divided into invisible handles and general handles. Personally think that the aluminum alloy invisible (full body) handle is the best, mainly because it does not occupy space, it will not touch people, but some people say that it is not convenient for hygiene.
The cabinet pendant is equipped with a special assembly for the cabinet. The hanging piece is fixed on the wall surface, and the hanging code is fixed on both sides of the left and right upper corners of the hanging cabinet. After hanging up, the upper and lower and front and rear positioning adjustments can be performed. Finally, the “body combination device†is installed to ensure the fixing quality and use. effect. Quality requirements for special assemblies: Each lifting code should be able to withstand a vertical lifting force of 50KG; it has a three-dimensional adjustment function; plastic parts should be flame retardant, free of cracks and marks. In order to save costs, some small manufacturers use screws to fix the wall cabinets. This method is neither beautiful nor safe, and it is troublesome to adjust the position.
The skirting kicks are made of cabinet material, PVC and aluminum alloy. The main function is to prevent debris from entering the lower part of the cabinet, and the other is aesthetic. Open the skirting board of the cabinet, you can see that there are four adjusting feet supporting the cabinet at the bottom of each cabinet. Each adjustment foot should be able to withstand a capacity of not less than 100kg; the material of the adjustment foot should be ABS to ensure its strength meets the load bearing requirements. The legs of the cabinet are generally 12CM high.
The storage hardware is made of metal materials such as stainless steel, which can make full use of the space hardware, easy to use and clean the kitchen environment, including seasoning basket, three-side basket, four-side basket, corner basket, high-deep basket, Lift storage basket, turntable basket, rice box, trash can, cutlery tray, etc.
Custom Aluminum Alloy Die Casting Tooling for Auto part, applicance, Electronic Enclosure etc
For Aluminium die casting products
Used Die cast Machine (Depend on mould) :Die casting machine 120 ton -800 ton
Main Processes Flow (depends on part shape and requirement):
Drawing / or Samples →Mould making →Die casting →Deburring →Drilling and Tapping →CNC Machining →Polish →Surface treatment →Assembly →Quality inspection → Packing →Shipping
Production Flow: Drawing/ or samples → Mould making →Die casting and other processes →Get samples and send samples to customer for approval → Mass Production ( casual inspection avoid unintentional situation) → QC → Packing →Shipping →Cycle to next order
Die Casting Mould,Auto Moulds,Aluminum Die Casting Mould,Aluminum Auto Parts Mold
Dongguan Hongge Hardware Technology Co., Ltd , http://www.honggecasting.com